The short answer

A standard shower in a Northern Virginia home runs about 2.5 gallons a minute, so a 10-minute shower uses about 25 gallons. Before 1992, some showerheads ran as high as 5.5 gallons a minute. A lot of that water is hot, which makes the shower one of the hardest jobs your water heater has.

The part most people don’t know

EPA’s WaterSense showerhead page says showering is nearly 17 percent of the water a home uses indoors, close to 40 gallons a day for the average family, and more than 1.2 trillion gallons a year across the country. Federal rules (10 CFR 430.32) cap any showerhead made since January 1, 1994 at 2.5 gallons a minute at 80 psi, a limit that came from a 1992 law. Before that, the Department of Energy’s hot water guide says some showerheads ran as high as 5.5 gallons a minute. Fairfax Water’s conservation tips put an unrestricted showerhead at five to ten gallons a minute.

$29 Water Test and Plumbing Safety Check

A licensed plumber tests your water's hardness at your kitchen table, in grains per gallon, checks your water heater's age and health and walks the plumbing with photos. Book the $29 test

Most of it is hot water

The Water Research Foundation’s 2016 study of how homes use water found showers were 20 percent of indoor water use, and the average shower ran 7.8 minutes. In a group of 94 homes where the researchers measured hot water on its own, showers used about 39 percent of all the hot water. DOE’s home upgrades guide says water heating is nearly 20 percent of a home’s energy use and usually the second-largest energy expense, after heating and cooling. Put those together and the shower is where a big share of your water heater’s work goes.

An installed white tankless water heater on a block basement wall in a Northern Virginia home
A tankless water heater on a basement wall. Showers are where a big share of any water heater’s work goes.

Why the hot water runs out

A tank heater holds a set amount of hot water. Two long showers back to back can drain it, and in winter the water coming in is colder, so the tank has more heating to do. Here’s why hot water runs out faster in winter and why it takes so long to get hot water. A tankless heater heats water as it flows, so it doesn’t run out the same way, but it can only heat so many gallons a minute at once. Here’s tank vs tankless in Northern Virginia.

A tankless water heater mounted on a basement wall with copper lines and a gray flue in a Northern Virginia home
A tankless heater heats water as it flows, so it doesn’t run out like a tank, but it can only heat so many gallons a minute at once.

What a newer showerhead changes

EPA says a WaterSense labeled showerhead uses no more than 2.0 gallons a minute, against the 2.5 standard. Swapping one in could save the average family 2,700 gallons of water a year and more than 330 kilowatt hours of electricity, enough to power a house for 11 days. Loudoun Water uses the same math for the old standard: about 25 gallons for a 10-minute shower. And EPA’s leak page says a showerhead leaking 10 drips a minute wastes more than 500 gallons a year.

A tankless water heater with copper piping and an expansion tank on a basement wall in a Northern Virginia home
Copper hot and cold lines at a tankless heater. Every gallon a showerhead saves is a gallon this never has to heat.

What you can check yourself

  • The bucket test. DOE’s test: hold a bucket marked at one gallon under the showerhead and time it. If it fills in under 20 seconds, the head is running more than 3 gallons a minute and a low-flow head would help.
  • The age. The 2.5 cap covers showerheads made since 1994. An original head in an older house may run well over it.
  • The water heater setting. If you run the shower almost all the way hot to be comfortable, check the tank. Here’s the right water heater temperature.
  • The pressure. A weak shower is often a clogged head or low house pressure, not the heater. Here’s what low pressure in the whole house means. Over 80 psi wears out valves and cartridges; here’s what a pressure reducing valve does.
  • The drip. A head that drips after you shut it off wastes water all day. Here’s what a dripping faucet wastes.

What we check

Our shower repair plumbers fix a shower that drips, runs cold or won’t shut off, and tell you if the water heater is the real problem.

If the tank is the problem, our water heater estimator shows your installed price first, then $500 comes off a new water heater, any size, replaced by our own plumbers.

A tank that’s never been flushed builds up sediment on the bottom. Our water heater flush is $99: we drain and flush the tank, check the anode rod and test the relief valve, then go through the house’s plumbing with photos, included.

Water heater flashing a code or a blinking light? Our error codes and warning lights guide covers what each one means.

Book it

Book the water heater flush, call (703) 997-9757, or book online from goswiftpro.com/cookiesoffer and a box of warm cookies comes with the visit. Rated 5.0 stars across 1,138 reviews on Google, Angi, Yelp, the BBB and Facebook, Virginia Class A license 2705192276.

Questions people ask

How much water does a 10-minute shower use?

About 25 gallons with a standard 2.5 gallon a minute showerhead, per Loudoun Water. A WaterSense labeled head uses 2.0 gallons a minute or less.

How many gallons a minute does a shower use?

Federal rules cap showerheads made since 1994 at 2.5 gallons a minute. DOE says some heads made before 1992 ran as high as 5.5.

How much of my hot water goes to showers?

In the Water Research Foundation’s 2016 study, showers used about 39 percent of household hot water in the homes where hot water was measured on its own.

How do I know if my showerhead uses too much water?

Time how long it takes to fill a one-gallon bucket. DOE says if it’s under 20 seconds, a low-flow showerhead would help.